Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Savage, MN to inspect, repair, and replace with zero guesswork.
Forge Siding grew out of a simple frustration: too many Savage homeowners were paying good money for Siding work that failed inside five years. Wrong profiles, wrong fastener gauges, no housewrap — then the callbacks never came. We do it right the first time, using manufacturer-recommended installation methods and materials rated for MN's specific climate demands.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Siding doesn't fail overnight — it gives you warning signs first. Catch them early and a repair handles it. Miss them, and you're looking at rot, mold, and structural repairs on top of the siding bill.
Even a small gap at a butt joint or around a window trim is an entry point. Water wicks in, freeze-thaw cycles widen the gap, and the damage compounds every winter.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Paint peeling on your inside walls near exterior surfaces is a classic sign that moisture is migrating inward through failing siding. By the time you see it inside, the wall cavity is already compromised.
A missing panel after a wind event or impact isn't just cosmetic damage. That exposed sheathing is collecting rain until you replace it. This is one repair that can't wait for a convenient schedule.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Heavy algae or mold staining on the exterior surface isn't just cosmetic — it means the surface is retaining moisture long enough for organic growth. That moisture is also working its way into the wall system.
Every job below starts with a free written estimate. We specify the product, the profile, the color, and the installation method upfront — so there's no ambiguity when work begins.
Fiber cement is the workhorse material we recommend most in MN's climate — it handles humidity, impact, and UV better than most alternatives and carries manufacturer warranties that actually hold up. We're certified installers for HardiePlank, HardieShingle, and competing fiber cement systems. Installation follows manufacturer specs to the millimeter: correct lap, correct fastener type and spacing, correct clearance from grade and roof surface, and full housewrap integration on every project.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for MN's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
LP SmartSide and similar engineered wood products split the difference between the look of real wood and the dimensional stability of manufactured products. They're primed at the factory, accept field-applied paint well, and hold up to impact and moisture better than OSB or solid wood. We use LP SmartSide Trim & Fascia alongside the panel and lap systems so the trim package matches — no mixing incompatible products that age differently.
Not every siding problem needs a full re-side. Storm impact, vandalism, or isolated rot can often be addressed with a targeted repair that blends into the existing field. We stock common profiles and can often source discontinued patterns through our supplier network for historic or older homes where matching matters. Partial replacement work is priced honestly — if we see a repair scope that's going to creep, we say so before we start, not after.
Commercial and multi-unit projects have different demands — larger panel formats, longer exposure to foot traffic and equipment contact, stricter fire ratings in some occupancy classes, and coordinated scheduling with other trades. Forge Siding handles commercial cladding projects in Savage, MN with full project management: dedicated site supervisor, daily progress reporting, and material delivery coordinated to minimize storage and laydown area on constrained sites.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
Installation follows manufacturer specs and local building code. When work is complete, the lead installer does a quality check before calling you for the final walkthrough. You inspect every elevation — we go through it with you, address anything that needs attention, and make sure the site is clean and restored before we invoice.
Every crew that works on your home carries a current contractor's license for MN, full general liability, and workers' compensation. We'll email you the certificates before we arrive — not after you ask three times.
You see the number before you sign — and the invoice matches the estimate. If scope changes come up during demo, we stop work, show you what we found, and get written approval before proceeding. No invoice surprises.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Get the Details on Our Warranty — +1-844-782-0929We don't cherry-pick — these are verbatim accounts from homeowners who hired us for Siding work across Savage, MN.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
I manage a twelve-unit building in Savage and we needed LP SmartSide on three facades before winter. Forge Siding coordinated with our property manager, worked around tenant schedules, delivered materials in two staged drops to keep the lot clear, and finished four days ahead of the original schedule. Commercial billing was clean and documented. They're on our preferred vendor list now.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
The estimate process was refreshingly honest. The estimator told me upfront that my old OSB sheathing had delaminated in two areas and would need replacement before new siding could go on — with photos and a written line item. No one had mentioned that in the other quotes. Forge Siding fixed the sheathing, installed the HardiePanel system, and the project cost exactly what they quoted including the repair.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Savage, MN don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
Real questions, real answers — no filler.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Savage, MN. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Our primary service area covers Savage and surrounding communities within our regional radius. Call +1-844-782-0929 to confirm service availability at your address — we'll tell you same-day.
Don't let failing siding go another season. Call Forge Siding and we'll have an estimator out to your property within 24 hours.
Schedule My Assessment — +1-844-782-0929